{"id":1087,"date":"2021-04-27T17:05:18","date_gmt":"2021-04-27T21:05:18","guid":{"rendered":"https:\/\/opentextbc.ca\/autocad3d\/chapter\/mass-properties\/"},"modified":"2021-11-04T11:39:53","modified_gmt":"2021-11-04T15:39:53","slug":"mass-properties","status":"publish","type":"chapter","link":"https:\/\/opentextbc.ca\/autocad3d\/chapter\/mass-properties\/","title":{"raw":"Module 25 Mass Properties","rendered":"Module 25 Mass Properties"},"content":{"raw":"
\n

Learning Outcomes<\/p>\n\n<\/header>\n

\n\nWhen you have completed this module, you will be able to:\n
    \n \t
  1. Describe and apply the MASSPROP commands to find the mass properties of solid models.<\/li>\n<\/ol>\n<\/div>\n<\/div>\n

    Geometry Lesson: Mass Properties<\/h1>\nThe mass properties <\/em><\/span>of a solid object are its mass, centre of gravity, centroid, volume, moments of inertia, products of inertia and radii of gyration. Since the mass refers to a solid object, you can only find the mass properties of a solid model. AutoCAD expresses the mass properties in inches. The mass properties include the following:\n\n\n\n\n\n\n\n\n\n\n
    Mass<\/th>\nthe quantity of the matter contained in the solid object. This is determined by the density of the material and the volume of the solid. Mass is not dependent on gravity which makes it different but proportional to weight. Mass is used when considering a measure of a solid\u2019s resistance to inertia.<\/td>\n<\/tr>\n
    Volume<\/th>\nThe amount of space occupied by the solid object.<\/td>\n<\/tr>\n
    Bounding box<\/th>\nThe smallest possible box that the object will fit inside. The box is constructed on the XYZ axis.<\/td>\n<\/tr>\n
    Centroid<\/th>\nGeometrical centre of the object. If the density of the object is uniform, the centroid is the centre of the mass or the centre of gravity.<\/td>\n<\/tr>\n
    Moments of Inertia<\/th>\nIs the measure of how the mass is distributed around XYZ axis of the current UCS. The values in the moments of inertia are a measure of the objects resistance to angular acceleration and are used when calculating the stress on the object.<\/td>\n<\/tr>\n
    Products of Inertia<\/th>\nSimilar to moments of inertia, the products of inertia measures the objects resistance to the angular acceleration, except it measures it around each 2D Axis (XY YZ XZ).<\/td>\n<\/tr>\n
    Radii of Gyration<\/th>\nIf the object was a uniform solid, with no holes, the radii of gyration would be the radius the moments of inertia would use to perform its calculations around each axis.<\/td>\n<\/tr>\n
    Principal Moments of XYZ Direction<\/th>\nThis is a measure of the maximum moments of inertia around an axis. When they are maximum, the principle moments are zero.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
    \n\nMUST KNOW: <\/strong>Since AutoCAD cannot assign a material to a solid model, the volume and mass of a solid will be identical. This is because AutoCAD assigns the density of 1 to all solids. To calculate the weight of the solid model, do the following:\n\nThe formula to calculate mass or weight of the solid is:\n\nmass= volume X density\n\nFollowing is a list of the density for three common materials. You can find the density of all materials by searching for lists on the internet.\n\nSteel - 0.2836 lb\/in3\n\nCopper - 0.3237 lb\/in3\n\nAluminum - 0.0975 lb\/in3\n\nFor example, the weight of a cubic foot of steel compared to a cubic foot of aluminum:\n\nSteel - 1728 in3 x 0.2836 = 490.06 lbs\n\nAluminum - 1728 in3 x 0.0975 = 168.48 lbs\n\nHint: (12\"X12\"X12\"=1728 in3)\n\nKeep in mind that AutoCAD always works in inches.\n\n<\/div>\n
    \n

    AutoCAD Command: MASSPROP<\/p>\n\n<\/header>\n

    \n\nThe MASSPROP command is used to compute and display the mass properties of a solid model or a region.\n\nShortcut: none\n\n[caption id=\"attachment_1074\" align=\"aligncenter\" width=\"359\"]\"\" Inquiry Toolbar[\/caption]\n\n[caption id=\"attachment_1074\" align=\"aligncenter\" width=\"480\"]\"\" Tools Pull-down[\/caption]\n\n<\/div>\n<\/div>\n

    WORK ALONG: Finding the Mass Properties of Solids and Regions<\/h1>\n

    Step 1<\/h2>\nStart a new drawing using the template: 3D Layout English<\/span>. Save the drawing with the name: AutoCAD 3D Workalong 25-1<\/span>\n

    Step 2<\/h2>\nUsing the INSERT command, insert the block: AutoCAD 3D Workalong 25-1<\/span> at the coordinates 0,0,0. Explode the block. Do not explode the solids. Change the solid models to layer: Solid 2<\/span>.\n
    AUTHOR'S COMMENTS: <\/strong> Use the Properties window to ensure that the objects are solid models.<\/div>\n

    Step 3<\/h2>\nSet the current view to SE Isometric, the current UCS to World and the current visual style to Realistic. Your drawing should appear as shown in the figure. (Figure Step 3)\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"313\"]\"\" Figure Step 3[\/caption]\n

    Step 4<\/h2>\nEnter the MASSPROP command, as shown below, selecting the solid model on the left side.\n\nCommand: MASSPROP<\/strong>\n\nSelect objects: 1 found\n\n(Select the solid model on the left.)<\/em><\/span>\n\nSelect objects:\n\nSOLIDS\n\n\n\n\n\n\n\n\n\n\n
    Mass:<\/th>\n19.0166<\/td>\n<\/tr>\n
    Volume:<\/th>\n19.0166Creating Solid Models Using Boxes, Wedges and Cylinder<\/td>\n<\/tr>\n
    Bounding box:<\/th>\nX: 0.0000----- 4.0000\n\nY: 0.0000----- 3.0000\n\nZ: 0.0000----- 4.0000<\/td>\n<\/tr>\n
    Centroid:X:<\/th>\n1.1528\n\nY: 1.5000\n\nZ: 1.8564<\/td>\n<\/tr>\n
    Moments of inertia:<\/th>\n\u00a0X: 159.7292\n\nY: 147.0995\n\nZ: 101.3495<\/td>\n<\/tr>\n
    Products of inertia:<\/th>\nXY: 32.8824\n\nYZ: 52.9538\n\nZX: 35.1506<\/td>\n<\/tr>\n
    Radii of gyration:<\/th>\nX: 2.8982\n\nY: 2.7812\n\nZ: 2.3086<\/td>\n<\/tr>\n
    Principal moments and X-Y-Z directions about centroid:<\/th>\nI: 52.9685 along [0.9625 0.0000 0.2712]\n\nJ: 56.2930 along [0.0000 1.0000 0.0000]\n\nK: 31.7293 along [-0.2712 0.0000 0.9625]<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\nWrite analysis to a file? [Yes\/No] <N>:\n\n(Accept No as the default.)<\/em><\/span>\n\nCommand:\n

    Step 5<\/h2>\nEnter the MASSPROP command again and select the solid model on the right side.\n\nCommand: MASSPROP<\/strong>\n\nSelect objects: 1 found\n\n(Select the solid on the right.)<\/em><\/span>\n\nSelect objects:\n\nSOLIDS<\/strong>\n\n\n\n\n\n\n\n\n\n\n
    Mass:<\/td>\n18.8792<\/td>\n<\/tr>\n
    Volume:<\/td>\n18.8792<\/td>\n<\/tr>\n
    Bounding box:<\/td>\nX: 0.0000----- 4.0000\n\nY: 8.0000----- 11.0000\n\nZ: 0.0000----- 4.0000<\/td>\n<\/tr>\n
    Centroid:X:<\/td>\nX: 1.1424\n\nY: 9.5154\n\nZ: 1.8485<\/td>\n<\/tr>\n
    Moments of inertia:<\/td>\nX: 1824.7216\n\nY: 144.5649\n\nZ: 1766.8808<\/td>\n<\/tr>\n
    Products of inertia:<\/td>\nXY: 205.9529\n\nYZ: 331.6084\n\nZX: 34.1723<\/td>\n<\/tr>\n
    Radii of gyration:<\/td>\nX: 9.8312\n\nY: 2.7672\n\nZ: 9.6741<\/td>\n<\/tr>\n
    Principal moments and X-Y-Z directions about centroid:<\/td>\nI: 52.3639 along [0.9426 0.1825 0.2795]\n\nJ: 55.5396 along [-0.1827 0.9828 -0.0257]\n\nK: 31.1772 along [-0.2793 -0.0269 0.9598]<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\nWrite analysis to a file? [Yes\/No] <N>: Y<\/strong>\n\n(This time enter Y to write the data to a file.)<\/em><\/span>\n\nCommand:\n

    Step 6<\/h2>\nEntering Y for yes will open the Create Mass and Area Properties File dialogue box. Save the file in the Lab Exercises folder assign it the same name as the drawing. The extension .mpr is automatically added.\n
    AUTHOR'S COMMENTS: <\/strong>The extension for the Mass and Area Properties File is .mpr. Once you save the mass properties data in the text file you can use the data in other programs or calculations. This saves you retyping the numbers or writing them down and eliminates the possibility of making errors.<\/div>\n
    AUTHOR'S COMMENTS: <\/strong>The Notepad program that comes with Windows is a very useful program to use when working with text files in AutoCAD. It is just a simple text editor but what makes it unique is that it works with pure text characters only. It does not add any special characters like fonts and bolding. This is important when the AutoCAD program has to use the text file.<\/div>\n

    Step 7<\/h2>\nStart Notepad. (Figure Step 7)\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"550\"]\"\" Figure Step 7[\/caption]\n

    Step 8<\/h2>\nIn Notepad, open the file: AutoCAD 3D Workalong 25-1.mpr<\/span> in the folder you saved it in. (Figure Step 8A, 8B, and 8C)\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"347\"]\"\" Figure Step 8A[\/caption]\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"628\"]\"\" Figure Step 8B[\/caption]\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"550\"]\"\" Figure Step 8C[\/caption]\n

    Step 9<\/h2>\nIn the Notepad window, you can find the centroid as shown below. This is the centre of gravity of the model.\n\nCentroid: X: 1.1424\n\nY: 9.5154\n\nZ: 1.8485\n

    Step 10<\/h2>\nOn layer: Construction<\/span>, insert a point at the centroid of the model using the POINT command as shown below. Change the point style and your model should appear similar to the figure. The shaded model rotated also is displaying a point at the centroid. (Figure Step 10A and 10B)\n\nCommand: POINT<\/strong>\n\nCurrent point modes: PDMODE=34\n\nPDSIZE=0.0000\n\nSpecify a point: 1.1424,9.5154,1.8485<\/strong>\n\nCommand:\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"235\"]\"\" Figure Step 10A[\/caption]\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"237\"]\"\" Figure Step 10B[\/caption]\n

    Step 11<\/h2>\nCalculate and record the weight of the solid model made out of aluminum and steel. See MUST KNOW in Geometry Lesson: Mass Properties. Check your answers after Step 18.<\/span>\n\nSteel -_____________ lbs\n\nAluminum -________ lbs\n
    AUTHOR'S COMMENTS:\u00a0<\/strong>See the MUST KNOW\u00a0under Geometry Lesson: Mass Properties.<\/div>\n

    Step 12<\/h2>\nUsing what you learned previously, offset a construction line 0.5 units from the far chamfered edge of the model on its right side. (Figure Step 12)\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"365\"]\"\" Figure Step 12[\/caption]\n

    Step 13<\/h2>\nLocate the Top UCS at the end of the line (Figure Step 13)\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"228\"]\"\" Figure Step 13[\/caption]\n

    Step 14<\/h2>\nUsing what you learned in Module 20, use the SECTION command, as shown below, to create a section at the location of the construction line you just drew. (Figure Step 14)\n\nCommand: SECTION<\/strong>\n\nSelect objects: 1 found\n\nSelect objects: Specify first point on Section plane by\n\n[Object\/Zaxis\/View\/XY\/YZ\/ZX\/3points] <3points>: ZX<\/strong>\n\nSpecify a point on the ZX-plane <0,0,0>:\n\nCommand:\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"228\"]\"\" Figure Step 14[\/caption]\n

    Step 15<\/h2>\nMove the region you just created outside of the model. It is not important where you locate it. Shaded and rotated, your model should appear similar to the figure. (Figure Step 15).\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"232\"]\"\" Figure Step 15[\/caption]\n

    Step 16<\/h2>\nUsing the MASSPROP command, as shown below, find the mass properties of the region.\n\nCommand: MASSPROP<\/strong>\n\nSelect objects: 1 found\n\n(Select the region.)<\/em><\/span>\n\nSelect objects:\n\nREGIONS\n\n\n\n\n\n\n
    Area:<\/td>\n6.4844<\/td>\n<\/tr>\n
    Perimeter:<\/td>\n19.8536<\/td>\n<\/tr>\n
    Bounding box<\/td>\nX: 3.8918 -- 7.8918\n\nY: 0.0000 -- 0.0000\n\nZ: -4.0000 -- 0.0000<\/td>\n<\/tr>\n
    Centroid:<\/td>\nX: 5.0834\n\nY: 0.0000\n\nZ: -2.1397<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\nWrite analysis to a file? [Yes\/No] <N>: N<\/strong>\n\nCommand:\n

    Step 17<\/h2>\nUsing what you learned earlier in this module, insert a point at the centroid of the region as shown in the figure. (Figure Step 17)\n\n[caption id=\"attachment_1085\" align=\"aligncenter\" width=\"440\"]\"\" Figure Step 17[\/caption]\n

    Step 18<\/h2>\nSave and close the drawing.\n\nAnswers from Step 11\n\nSteel - 5.3541 lbs\n\nAluminum - 1.8407 lbs\n

    Key Principles<\/h1>\n
    \n

    Key Principles in Module 25<\/p>\n\n<\/header>\n

    \n
      \n \t
    1. Mass properties can only be found for solid models and regions.<\/li>\n \t
    2. The formula to calculate mass or weight of a solid is: mass= volume X density<\/li>\n \t
    3. AutoCAD always works in inches and reports the mass properties in inches regardless of the what units the drawing was constructed in.<\/li>\n<\/ol>\n<\/div>\n<\/div>","rendered":"
      \n
      \n

      Learning Outcomes<\/p>\n<\/header>\n

      \n

      When you have completed this module, you will be able to:<\/p>\n

        \n
      1. Describe and apply the MASSPROP commands to find the mass properties of solid models.<\/li>\n<\/ol>\n<\/div>\n<\/div>\n

        Geometry Lesson: Mass Properties<\/h1>\n

        The mass properties <\/em><\/span>of a solid object are its mass, centre of gravity, centroid, volume, moments of inertia, products of inertia and radii of gyration. Since the mass refers to a solid object, you can only find the mass properties of a solid model. AutoCAD expresses the mass properties in inches. The mass properties include the following:<\/p>\n\n\n\n\n\n\n\n\n\n\n
        Mass<\/th>\nthe quantity of the matter contained in the solid object. This is determined by the density of the material and the volume of the solid. Mass is not dependent on gravity which makes it different but proportional to weight. Mass is used when considering a measure of a solid\u2019s resistance to inertia.<\/td>\n<\/tr>\n
        Volume<\/th>\nThe amount of space occupied by the solid object.<\/td>\n<\/tr>\n
        Bounding box<\/th>\nThe smallest possible box that the object will fit inside. The box is constructed on the XYZ axis.<\/td>\n<\/tr>\n
        Centroid<\/th>\nGeometrical centre of the object. If the density of the object is uniform, the centroid is the centre of the mass or the centre of gravity.<\/td>\n<\/tr>\n
        Moments of Inertia<\/th>\nIs the measure of how the mass is distributed around XYZ axis of the current UCS. The values in the moments of inertia are a measure of the objects resistance to angular acceleration and are used when calculating the stress on the object.<\/td>\n<\/tr>\n
        Products of Inertia<\/th>\nSimilar to moments of inertia, the products of inertia measures the objects resistance to the angular acceleration, except it measures it around each 2D Axis (XY YZ XZ).<\/td>\n<\/tr>\n
        Radii of Gyration<\/th>\nIf the object was a uniform solid, with no holes, the radii of gyration would be the radius the moments of inertia would use to perform its calculations around each axis.<\/td>\n<\/tr>\n
        Principal Moments of XYZ Direction<\/th>\nThis is a measure of the maximum moments of inertia around an axis. When they are maximum, the principle moments are zero.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
        \n

        MUST KNOW: <\/strong>Since AutoCAD cannot assign a material to a solid model, the volume and mass of a solid will be identical. This is because AutoCAD assigns the density of 1 to all solids. To calculate the weight of the solid model, do the following:<\/p>\n

        The formula to calculate mass or weight of the solid is:<\/p>\n

        mass= volume X density<\/p>\n

        Following is a list of the density for three common materials. You can find the density of all materials by searching for lists on the internet.<\/p>\n

        Steel – 0.2836 lb\/in3<\/p>\n

        Copper – 0.3237 lb\/in3<\/p>\n

        Aluminum – 0.0975 lb\/in3<\/p>\n

        For example, the weight of a cubic foot of steel compared to a cubic foot of aluminum:<\/p>\n

        Steel – 1728 in3 x 0.2836 = 490.06 lbs<\/p>\n

        Aluminum – 1728 in3 x 0.0975 = 168.48 lbs<\/p>\n

        Hint: (12″X12″X12″=1728 in3)<\/p>\n

        Keep in mind that AutoCAD always works in inches.<\/p>\n<\/div>\n

        \n
        \n

        AutoCAD Command: MASSPROP<\/p>\n<\/header>\n

        \n

        The MASSPROP command is used to compute and display the mass properties of a solid model or a region.<\/p>\n

        Shortcut: none<\/p>\n

        \"\"
        Inquiry Toolbar<\/figcaption><\/figure>\n
        \"\"
        Tools Pull-down<\/figcaption><\/figure>\n<\/div>\n<\/div>\n

        WORK ALONG: Finding the Mass Properties of Solids and Regions<\/h1>\n

        Step 1<\/h2>\n

        Start a new drawing using the template: 3D Layout English<\/span>. Save the drawing with the name: AutoCAD 3D Workalong 25-1<\/span><\/p>\n

        Step 2<\/h2>\n

        Using the INSERT command, insert the block: AutoCAD 3D Workalong 25-1<\/span> at the coordinates 0,0,0. Explode the block. Do not explode the solids. Change the solid models to layer: Solid 2<\/span>.<\/p>\n

        AUTHOR’S COMMENTS: <\/strong> Use the Properties window to ensure that the objects are solid models.<\/div>\n

        Step 3<\/h2>\n

        Set the current view to SE Isometric, the current UCS to World and the current visual style to Realistic. Your drawing should appear as shown in the figure. (Figure Step 3)<\/p>\n

        \"\"
        Figure Step 3<\/figcaption><\/figure>\n

        Step 4<\/h2>\n

        Enter the MASSPROP command, as shown below, selecting the solid model on the left side.<\/p>\n

        Command: MASSPROP<\/strong><\/p>\n

        Select objects: 1 found<\/p>\n

        (Select the solid model on the left.)<\/em><\/span><\/p>\n

        Select objects:<\/p>\n

        SOLIDS<\/p>\n\n\n\n\n\n\n\n\n\n\n
        Mass:<\/th>\n19.0166<\/td>\n<\/tr>\n
        Volume:<\/th>\n19.0166Creating Solid Models Using Boxes, Wedges and Cylinder<\/td>\n<\/tr>\n
        Bounding box:<\/th>\nX: 0.0000—– 4.0000<\/p>\n

        Y: 0.0000—– 3.0000<\/p>\n

        Z: 0.0000—– 4.0000<\/td>\n<\/tr>\n

        Centroid:X:<\/th>\n1.1528<\/p>\n

        Y: 1.5000<\/p>\n

        Z: 1.8564<\/td>\n<\/tr>\n

        Moments of inertia:<\/th>\n\u00a0X: 159.7292<\/p>\n

        Y: 147.0995<\/p>\n

        Z: 101.3495<\/td>\n<\/tr>\n

        Products of inertia:<\/th>\nXY: 32.8824<\/p>\n

        YZ: 52.9538<\/p>\n

        ZX: 35.1506<\/td>\n<\/tr>\n

        Radii of gyration:<\/th>\nX: 2.8982<\/p>\n

        Y: 2.7812<\/p>\n

        Z: 2.3086<\/td>\n<\/tr>\n

        Principal moments and X-Y-Z directions about centroid:<\/th>\nI: 52.9685 along [0.9625 0.0000 0.2712]<\/p>\n

        J: 56.2930 along [0.0000 1.0000 0.0000]<\/p>\n

        K: 31.7293 along [-0.2712 0.0000 0.9625]<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

        Write analysis to a file? [Yes\/No] <N>:<\/p>\n

        (Accept No as the default.)<\/em><\/span><\/p>\n

        Command:<\/p>\n

        Step 5<\/h2>\n

        Enter the MASSPROP command again and select the solid model on the right side.<\/p>\n

        Command: MASSPROP<\/strong><\/p>\n

        Select objects: 1 found<\/p>\n

        (Select the solid on the right.)<\/em><\/span><\/p>\n

        Select objects:<\/p>\n

        SOLIDS<\/strong><\/p>\n\n\n\n\n\n\n\n\n\n\n
        Mass:<\/td>\n18.8792<\/td>\n<\/tr>\n
        Volume:<\/td>\n18.8792<\/td>\n<\/tr>\n
        Bounding box:<\/td>\nX: 0.0000—– 4.0000<\/p>\n

        Y: 8.0000—– 11.0000<\/p>\n

        Z: 0.0000—– 4.0000<\/td>\n<\/tr>\n

        Centroid:X:<\/td>\nX: 1.1424<\/p>\n

        Y: 9.5154<\/p>\n

        Z: 1.8485<\/td>\n<\/tr>\n

        Moments of inertia:<\/td>\nX: 1824.7216<\/p>\n

        Y: 144.5649<\/p>\n

        Z: 1766.8808<\/td>\n<\/tr>\n

        Products of inertia:<\/td>\nXY: 205.9529<\/p>\n

        YZ: 331.6084<\/p>\n

        ZX: 34.1723<\/td>\n<\/tr>\n

        Radii of gyration:<\/td>\nX: 9.8312<\/p>\n

        Y: 2.7672<\/p>\n

        Z: 9.6741<\/td>\n<\/tr>\n

        Principal moments and X-Y-Z directions about centroid:<\/td>\nI: 52.3639 along [0.9426 0.1825 0.2795]<\/p>\n

        J: 55.5396 along [-0.1827 0.9828 -0.0257]<\/p>\n

        K: 31.1772 along [-0.2793 -0.0269 0.9598]<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

        Write analysis to a file? [Yes\/No] <N>: Y<\/strong><\/p>\n

        (This time enter Y to write the data to a file.)<\/em><\/span><\/p>\n

        Command:<\/p>\n

        Step 6<\/h2>\n

        Entering Y for yes will open the Create Mass and Area Properties File dialogue box. Save the file in the Lab Exercises folder assign it the same name as the drawing. The extension .mpr is automatically added.<\/p>\n

        AUTHOR’S COMMENTS: <\/strong>The extension for the Mass and Area Properties File is .mpr. Once you save the mass properties data in the text file you can use the data in other programs or calculations. This saves you retyping the numbers or writing them down and eliminates the possibility of making errors.<\/div>\n
        AUTHOR’S COMMENTS: <\/strong>The Notepad program that comes with Windows is a very useful program to use when working with text files in AutoCAD. It is just a simple text editor but what makes it unique is that it works with pure text characters only. It does not add any special characters like fonts and bolding. This is important when the AutoCAD program has to use the text file.<\/div>\n

        Step 7<\/h2>\n

        Start Notepad. (Figure Step 7)<\/p>\n

        \"\"
        Figure Step 7<\/figcaption><\/figure>\n

        Step 8<\/h2>\n

        In Notepad, open the file: AutoCAD 3D Workalong 25-1.mpr<\/span> in the folder you saved it in. (Figure Step 8A, 8B, and 8C)<\/p>\n

        \"\"
        Figure Step 8A<\/figcaption><\/figure>\n
        \"\"
        Figure Step 8B<\/figcaption><\/figure>\n
        \"\"
        Figure Step 8C<\/figcaption><\/figure>\n

        Step 9<\/h2>\n

        In the Notepad window, you can find the centroid as shown below. This is the centre of gravity of the model.<\/p>\n

        Centroid: X: 1.1424<\/p>\n

        Y: 9.5154<\/p>\n

        Z: 1.8485<\/p>\n

        Step 10<\/h2>\n

        On layer: Construction<\/span>, insert a point at the centroid of the model using the POINT command as shown below. Change the point style and your model should appear similar to the figure. The shaded model rotated also is displaying a point at the centroid. (Figure Step 10A and 10B)<\/p>\n

        Command: POINT<\/strong><\/p>\n

        Current point modes: PDMODE=34<\/p>\n

        PDSIZE=0.0000<\/p>\n

        Specify a point: 1.1424,9.5154,1.8485<\/strong><\/p>\n

        Command:<\/p>\n

        \"\"
        Figure Step 10A<\/figcaption><\/figure>\n
        \"\"
        Figure Step 10B<\/figcaption><\/figure>\n

        Step 11<\/h2>\n

        Calculate and record the weight of the solid model made out of aluminum and steel. See MUST KNOW in Geometry Lesson: Mass Properties. Check your answers after Step 18.<\/span><\/p>\n

        Steel -_____________ lbs<\/p>\n

        Aluminum -________ lbs<\/p>\n

        AUTHOR’S COMMENTS:\u00a0<\/strong>See the MUST KNOW\u00a0under Geometry Lesson: Mass Properties.<\/div>\n

        Step 12<\/h2>\n

        Using what you learned previously, offset a construction line 0.5 units from the far chamfered edge of the model on its right side. (Figure Step 12)<\/p>\n

        \"\"
        Figure Step 12<\/figcaption><\/figure>\n

        Step 13<\/h2>\n

        Locate the Top UCS at the end of the line (Figure Step 13)<\/p>\n

        \"\"
        Figure Step 13<\/figcaption><\/figure>\n

        Step 14<\/h2>\n

        Using what you learned in Module 20, use the SECTION command, as shown below, to create a section at the location of the construction line you just drew. (Figure Step 14)<\/p>\n

        Command: SECTION<\/strong><\/p>\n

        Select objects: 1 found<\/p>\n

        Select objects: Specify first point on Section plane by<\/p>\n

        [Object\/Zaxis\/View\/XY\/YZ\/ZX\/3points] <3points>: ZX<\/strong><\/p>\n

        Specify a point on the ZX-plane <0,0,0>:<\/p>\n

        Command:<\/p>\n

        \"\"
        Figure Step 14<\/figcaption><\/figure>\n

        Step 15<\/h2>\n

        Move the region you just created outside of the model. It is not important where you locate it. Shaded and rotated, your model should appear similar to the figure. (Figure Step 15).<\/p>\n

        \"\"
        Figure Step 15<\/figcaption><\/figure>\n

        Step 16<\/h2>\n

        Using the MASSPROP command, as shown below, find the mass properties of the region.<\/p>\n

        Command: MASSPROP<\/strong><\/p>\n

        Select objects: 1 found<\/p>\n

        (Select the region.)<\/em><\/span><\/p>\n

        Select objects:<\/p>\n

        REGIONS<\/p>\n\n\n\n\n\n\n
        Area:<\/td>\n6.4844<\/td>\n<\/tr>\n
        Perimeter:<\/td>\n19.8536<\/td>\n<\/tr>\n
        Bounding box<\/td>\nX: 3.8918 — 7.8918<\/p>\n

        Y: 0.0000 — 0.0000<\/p>\n

        Z: -4.0000 — 0.0000<\/td>\n<\/tr>\n

        Centroid:<\/td>\nX: 5.0834<\/p>\n

        Y: 0.0000<\/p>\n

        Z: -2.1397<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

        Write analysis to a file? [Yes\/No] <N>: N<\/strong><\/p>\n

        Command:<\/p>\n

        Step 17<\/h2>\n

        Using what you learned earlier in this module, insert a point at the centroid of the region as shown in the figure. (Figure Step 17)<\/p>\n

        \"\"
        Figure Step 17<\/figcaption><\/figure>\n

        Step 18<\/h2>\n

        Save and close the drawing.<\/p>\n

        Answers from Step 11<\/p>\n

        Steel – 5.3541 lbs<\/p>\n

        Aluminum – 1.8407 lbs<\/p>\n

        Key Principles<\/h1>\n
        \n
        \n

        Key Principles in Module 25<\/p>\n<\/header>\n

        \n
          \n
        1. Mass properties can only be found for solid models and regions.<\/li>\n
        2. The formula to calculate mass or weight of a solid is: mass= volume X density<\/li>\n
        3. AutoCAD always works in inches and reports the mass properties in inches regardless of the what units the drawing was constructed in.<\/li>\n<\/ol>\n<\/div>\n<\/div>\n","protected":false},"author":90,"menu_order":4,"template":"","meta":{"pb_show_title":"on","pb_short_title":"","pb_subtitle":"","pb_authors":[],"pb_section_license":""},"chapter-type":[],"contributor":[],"license":[],"class_list":["post-1087","chapter","type-chapter","status-publish","hentry"],"part":923,"_links":{"self":[{"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/pressbooks\/v2\/chapters\/1087","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/pressbooks\/v2\/chapters"}],"about":[{"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/wp\/v2\/types\/chapter"}],"author":[{"embeddable":true,"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/wp\/v2\/users\/90"}],"version-history":[{"count":1,"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/pressbooks\/v2\/chapters\/1087\/revisions"}],"predecessor-version":[{"id":1088,"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/pressbooks\/v2\/chapters\/1087\/revisions\/1088"}],"part":[{"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/pressbooks\/v2\/parts\/923"}],"metadata":[{"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/pressbooks\/v2\/chapters\/1087\/metadata\/"}],"wp:attachment":[{"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/wp\/v2\/media?parent=1087"}],"wp:term":[{"taxonomy":"chapter-type","embeddable":true,"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/pressbooks\/v2\/chapter-type?post=1087"},{"taxonomy":"contributor","embeddable":true,"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/wp\/v2\/contributor?post=1087"},{"taxonomy":"license","embeddable":true,"href":"https:\/\/opentextbc.ca\/autocad3d\/wp-json\/wp\/v2\/license?post=1087"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}