{"id":166,"date":"2021-08-13T13:22:04","date_gmt":"2021-08-13T17:22:04","guid":{"rendered":"https:\/\/opentextbc.ca\/patterndevelopment\/chapter\/pipe-on-a-miter\/"},"modified":"2023-01-24T13:08:27","modified_gmt":"2023-01-24T18:08:27","slug":"pipe-on-a-miter","status":"web-only","type":"chapter","link":"https:\/\/opentextbc.ca\/patterndevelopment\/chapter\/pipe-on-a-miter\/","title":{"raw":"Pipe on a Miter","rendered":"Pipe on a Miter"},"content":{"raw":"
    \r\n \t
  1. Draw a full [pb_glossary id=\"477\"]plan[\/pb_glossary] <\/strong>(top) and [pb_glossary id=\"499\"]elevation view[\/pb_glossary] <\/strong>(front) of the project, complete with the [pb_glossary id=\"485\"]miter[\/pb_glossary]<\/strong> line.\"\"<\/li>\r\n \t
  2. Divide the [pb_glossary id=\"477\"]plan view[\/pb_glossary]<\/strong> into 12 equal parts (see Divide a Circle Into 12 Equal Parts<\/a>) and label it. It is common practice to label a round object with numbers.\"\"<\/strong><\/li>\r\n \t
  3. Project the\u00a0plan view\u00a0divisions down into the\u00a0elevation view.\"\"<\/strong><\/li>\r\n \t
  4. Draw the\u00a0[pb_glossary id=\"479\"]stretch-out[\/pb_glossary]<\/strong>\u00a0directly to the right of the\u00a0elevation view\u00a0<\/strong>and divide it into 12 equal parts (see Divide a Line Using a Ruler on an Angle<\/a>). Label it to match the plan view and make sure to start the labeling where you want the seam. Add any required seam allowances outside of the stretch-out.\"\"<\/strong><\/li>\r\n \t
  5. At the points where the\u00a0[pb_glossary id=\"507\"]element lines[\/pb_glossary]<\/strong>\u00a0cross the\u00a0miter line, project them into the\u00a0stretch-out.\"\"<\/strong><\/li>\r\n \t
  6. Following the labeling, circle the intersection points on the\u00a0stretch-out. Don't put a dot over the points, but circle around them.<\/strong><\/li>\r\n \t
  7. Using a flexible curve, join the points to draw in the miter line,\u00a0completing the\u00a0[pb_glossary id=\"487\"]pattern[\/pb_glossary]<\/strong>.\"\"<\/strong><\/li>\r\n<\/ol>\r\nhttps:\/\/media.bccampus.ca\/id\/0_r7cht8gb?width=608&height=402&playerId=23449753","rendered":"
      \n
    1. Draw a full plan<\/a> <\/strong>(top) and elevation view<\/a> <\/strong>(front) of the project, complete with the miter<\/a><\/strong> line.\"\"<\/li>\n
    2. Divide the plan view<\/a><\/strong> into 12 equal parts (see Divide a Circle Into 12 Equal Parts<\/a>) and label it. It is common practice to label a round object with numbers.\"\"<\/strong><\/li>\n
    3. Project the\u00a0plan view\u00a0divisions down into the\u00a0elevation view.\"\"<\/strong><\/li>\n
    4. Draw the\u00a0stretch-out<\/a><\/strong>\u00a0directly to the right of the\u00a0elevation view\u00a0<\/strong>and divide it into 12 equal parts (see Divide a Line Using a Ruler on an Angle<\/a>). Label it to match the plan view and make sure to start the labeling where you want the seam. Add any required seam allowances outside of the stretch-out.\"\"<\/strong><\/li>\n
    5. At the points where the\u00a0element lines<\/a><\/strong>\u00a0cross the\u00a0miter line, project them into the\u00a0stretch-out.\"\"<\/strong><\/li>\n
    6. Following the labeling, circle the intersection points on the\u00a0stretch-out. Don’t put a dot over the points, but circle around them.<\/strong><\/li>\n
    7. Using a flexible curve, join the points to draw in the miter line,\u00a0completing the\u00a0pattern<\/a><\/strong>.\"\"<\/strong><\/li>\n<\/ol>\n