{"id":422,"date":"2021-08-13T13:22:58","date_gmt":"2021-08-13T17:22:58","guid":{"rendered":"https:\/\/opentextbc.ca\/patterndevelopment\/chapter\/off-centre-square-to-round\/"},"modified":"2023-01-24T13:23:28","modified_gmt":"2023-01-24T18:23:28","slug":"off-centre-square-to-round","status":"web-only","type":"chapter","link":"https:\/\/opentextbc.ca\/patterndevelopment\/chapter\/off-centre-square-to-round\/","title":{"raw":"Off-Centre Square to Round","rendered":"Off-Centre Square to Round"},"content":{"raw":"
The only difference with this fitting is a few more element line lengths than an on-centre, the process is exactly the same.<\/div>\r\n
    \r\n \t
  1. Draw a full [pb_glossary id=\"477\"]plan view[\/pb_glossary]<\/strong> complete with all [pb_glossary id=\"507\"]element lines[\/pb_glossary] <\/strong>and labeling. Choose a line of symmetry to place the seam so you only need to make 1 pattern. Label one half of the plan view, the round end with numbers and the square end with letters.\"\"<\/li>\r\n \t
  2. Create a [pb_glossary id=\"484\"]TLD[\/pb_glossary] <\/strong>and label it\r\n\"\"<\/li>\r\n \t
  3. Draw a baseline equal to line A-B.\r\n\"\"<\/li>\r\n \t
  4. Pick up the [pb_glossary id=\"476\"]true length[\/pb_glossary]<\/strong> of line A-4 and swing it from point A.\"\"<\/li>\r\n \t
  5. Next, pick up true length of line B-4 and swing it from point B. Where it crosses the first arc, becomes point 4.\"\"<\/li>\r\n \t
  6. Pick up a step-off from the plan view and swing it from point 4. Unlike an on-centre square to round, this fitting needs to be developed one side at a time. Complete one side, then go back to finish the other side.\"\"<\/strong><\/li>\r\n \t
  7. Pick up the true length of line A-3 and swing it from point A.\"\"<\/li>\r\n \t
  8. Pick a step-off and swing it from point 3.\"\"<\/li>\r\n \t
  9. Pick up the true length of line A-2 and swing it from point A.\"\"<\/li>\r\n \t
  10. Pick up a step-off and swing it from 2.\r\n\"\"<\/li>\r\n \t
  11. Pick up the true length of line A-1 and swing it from point A.\"\"<\/li>\r\n \t
  12. Pick up the true length of line D-1 and swing it from 1.\"\"<\/li>\r\n \t
  13. Pick up line A-D from the plan view (remember that letter to letter is true length) and swing it from point A. Remember that point D should be 90<\/strong>\u00b0. If it not, go back and check your work.\r\n\"\"<\/strong><\/li>\r\n \t
  14. Now, go back to point 4 and work the pattern to the other side, completing it at point C. Notice in this example, line C-7 has no length in the plan view, it is a dot. The true length is the [pb_glossary id=\"502\"]vertical[\/pb_glossary]<\/strong> height. Zero plan length put 90 deg to the vertical height, will have no change to the vertical height.\"\"<\/li>\r\n \t
  15. Draw in the all the element lines and outside edges, using a flexible curve for the round end.\"\"<\/li>\r\n<\/ol>\r\nhttps:\/\/media.bccampus.ca\/id\/0_js891yob?width=608&height=402&playerId=23449753\r\n\r\n ","rendered":"
    The only difference with this fitting is a few more element line lengths than an on-centre, the process is exactly the same.<\/div>\n
      \n
    1. Draw a full plan view<\/a><\/strong> complete with all element lines<\/a> <\/strong>and labeling. Choose a line of symmetry to place the seam so you only need to make 1 pattern. Label one half of the plan view, the round end with numbers and the square end with letters.\"\"<\/li>\n
    2. Create a TLD<\/a> <\/strong>and label it
      \n\"\"<\/li>\n
    3. Draw a baseline equal to line A-B.
      \n\"\"<\/li>\n
    4. Pick up the true length<\/a><\/strong> of line A-4 and swing it from point A.\"\"<\/li>\n
    5. Next, pick up true length of line B-4 and swing it from point B. Where it crosses the first arc, becomes point 4.\"\"<\/li>\n
    6. Pick up a step-off from the plan view and swing it from point 4. Unlike an on-centre square to round, this fitting needs to be developed one side at a time. Complete one side, then go back to finish the other side.\"\"<\/strong><\/li>\n
    7. Pick up the true length of line A-3 and swing it from point A.\"\"<\/li>\n
    8. Pick a step-off and swing it from point 3.\"\"<\/li>\n
    9. Pick up the true length of line A-2 and swing it from point A.\"\"<\/li>\n
    10. Pick up a step-off and swing it from 2.
      \n\"\"<\/li>\n
    11. Pick up the true length of line A-1 and swing it from point A.\"\"<\/li>\n
    12. Pick up the true length of line D-1 and swing it from 1.\"\"<\/li>\n
    13. Pick up line A-D from the plan view (remember that letter to letter is true length) and swing it from point A. Remember that point D should be 90<\/strong>\u00b0. If it not, go back and check your work.
      \n\"\"<\/strong><\/li>\n
    14. Now, go back to point 4 and work the pattern to the other side, completing it at point C. Notice in this example, line C-7 has no length in the plan view, it is a dot. The true length is the vertical<\/a><\/strong> height. Zero plan length put 90 deg to the vertical height, will have no change to the vertical height.\"\"<\/li>\n
    15. Draw in the all the element lines and outside edges, using a flexible curve for the round end.\"\"<\/li>\n<\/ol>\n

      https:\/\/media.bccampus.ca\/id\/0_js891yob?width=608&height=402&playerId=23449753<\/p>\n

       <\/p>\n

      definition<\/span>