{"id":448,"date":"2021-08-13T13:23:04","date_gmt":"2021-08-13T17:23:04","guid":{"rendered":"https:\/\/opentextbc.ca\/patterndevelopment\/chapter\/off-centre-round-taper\/"},"modified":"2023-01-24T13:24:14","modified_gmt":"2023-01-24T18:24:14","slug":"off-centre-round-taper","status":"web-only","type":"chapter","link":"https:\/\/opentextbc.ca\/patterndevelopment\/chapter\/off-centre-round-taper\/","title":{"raw":"Off-Centre Round Taper","rendered":"Off-Centre Round Taper"},"content":{"raw":"
    \r\n \t
  1. Draw a full [pb_glossary id=\"477\"]plan view[\/pb_glossary]<\/strong> complete with all [pb_glossary id=\"507\"]element lines[\/pb_glossary] <\/strong>and labeling. Label one half of the plan view, go from large end to small end, zigzagging back and forth with the numbering 1-14. Remember, every round to round will be on centre one way, but it is always worth drawing the whole thing.\"\"<\/strong><\/li>\r\n \t
  2. Create a\u00a0[pb_glossary id=\"484\"]TLD[\/pb_glossary]<\/strong>\u00a0and label all the\u00a0element lines.\"\"<\/strong><\/li>\r\n \t
  3. Draw a vertical line equal to the [pb_glossary id=\"476\"]true length[\/pb_glossary]<\/strong> of line 13-14.\"\"<\/li>\r\n \t
  4. From the\u00a0TLD, pick up the true length of line 13-12 and swing it from point 13 back towards point 14. Remember to work both sides at the same time.\"\"<\/strong><\/li>\r\n \t
  5. Next, pick up\u00a0step-off 14-12, and swing it from point 14.\"\"<\/li>\r\n \t
  6. Pick up line 12-11 from the TLD, and swing it from point 12.\"\"<\/li>\r\n \t
  7. Pick up step-off 11-13, and swing it from point 13.\"\"<\/li>\r\n \t
  8. Follow this same procedures, swing the true length of an\u00a0element line\u00a0and a\u00a0step-off to create the next point until you reach point 1.\"\"<\/li>\r\n \t
  9. Draw in the all the\u00a0element lines and outside edges, use a flexible curve for the round ends.\"\"<\/li>\r\n<\/ol>\r\nhttps:\/\/media.bccampus.ca\/id\/0_rlj21pf2?width=608&height=402&playerId=23449753","rendered":"
      \n
    1. Draw a full plan view<\/a><\/strong> complete with all element lines<\/a> <\/strong>and labeling. Label one half of the plan view, go from large end to small end, zigzagging back and forth with the numbering 1-14. Remember, every round to round will be on centre one way, but it is always worth drawing the whole thing.\"\"<\/strong><\/li>\n
    2. Create a\u00a0TLD<\/a><\/strong>\u00a0and label all the\u00a0element lines.\"\"<\/strong><\/li>\n
    3. Draw a vertical line equal to the true length<\/a><\/strong> of line 13-14.\"\"<\/li>\n
    4. From the\u00a0TLD, pick up the true length of line 13-12 and swing it from point 13 back towards point 14. Remember to work both sides at the same time.\"\"<\/strong><\/li>\n
    5. Next, pick up\u00a0step-off 14-12, and swing it from point 14.\"\"<\/li>\n
    6. Pick up line 12-11 from the TLD, and swing it from point 12.\"\"<\/li>\n
    7. Pick up step-off 11-13, and swing it from point 13.\"\"<\/li>\n
    8. Follow this same procedures, swing the true length of an\u00a0element line\u00a0and a\u00a0step-off to create the next point until you reach point 1.\"\"<\/li>\n
    9. Draw in the all the\u00a0element lines and outside edges, use a flexible curve for the round ends.\"\"<\/li>\n<\/ol>\n

      https:\/\/media.bccampus.ca\/id\/0_rlj21pf2?width=608&height=402&playerId=23449753<\/p>\n

      definition<\/span>