{"id":508,"date":"2019-06-11T14:51:22","date_gmt":"2019-06-11T14:51:22","guid":{"rendered":"https:\/\/opentextbc.ca\/physicalgeology2ed\/chapter\/11-4-the-impacts-of-earthquakes\/"},"modified":"2021-12-08T18:04:56","modified_gmt":"2021-12-08T18:04:56","slug":"11-4-the-impacts-of-earthquakes","status":"publish","type":"chapter","link":"https:\/\/opentextbc.ca\/physicalgeology2ed\/chapter\/11-4-the-impacts-of-earthquakes\/","title":{"raw":"11.4 The Impacts of Earthquakes","rendered":"11.4 The Impacts of Earthquakes"},"content":{"raw":"Some of the common impacts of earthquakes include structural damage to buildings, fires, damage to bridges, highways, pipelines and electrical transmission lines, initiation of slope failures, liquefaction, and tsunami. The types of impacts depend to a large degree on where the earthquake is located: whether it is predominantly urban or rural, densely or sparsely populated, highly developed or underdeveloped, and of course on the ability of the infrastructure to withstand shaking.\r\n\r\nAs we\u2019ve seen from the example of the 1985 Mexico earthquake, the geological foundations on which structures are built can have a significant impact on earthquake shaking. When an earthquake happens, the seismic waves produced have a wide range of frequencies. The energy of the higher frequency waves tends to be absorbed by solid rock, while the lower frequency waves (with periods slower than one second) pass through the solid rock without being absorbed, but are eventually absorbed and amplified by soft sediments. It is therefore very common to see much worse earthquake damage in areas underlain by soft sediments than in areas of solid rock. A good example of this is in the Oakland area near San Francisco, where parts of a two-layer highway built on soft sediments collapsed during the 1989 Loma Prieta earthquake (Figure 11.4.1).\r\n\r\n[caption id=\"attachment_498\" align=\"alignright\" width=\"600\"]\"\"<\/a> Figure 11.4.1 A part of the Cypress Freeway in Oakland California that collapsed during the 1989 Loma Prieta earthquake.[\/caption]\r\n\r\nBuilding damage is also greatest in areas of soft sediments, and multi-storey buildings tend to be more seriously damaged than smaller ones. Buildings can be designed to withstand most earthquakes, and this practice is increasingly applied in earthquake-prone regions. Turkey is one such region, and even though Turkey had a relatively strong building code in the 1990s, adherence to the code was poor, as builders did whatever they could to save costs, including using inappropriate materials in concrete and reducing the amount of steel reinforcing. The result was that there were over 17,000 deaths in the 1999 M7.6 Izmit earthquake (Figure 11.4.2). After two devastating earthquakes that year, Turkish authorities strengthened the building code further, but the new code has been applied only in a few regions, and enforcement of the code is still weak, as revealed by the amount of damage from a M7.1 earthquake in eastern Turkey in 2011.\r\n\r\n[caption id=\"attachment_499\" align=\"aligncenter\" width=\"900\"]\"\"<\/a> Figure 11.4.2 Buildings damaged by the 1999 earthquake in the Izmit area, Turkey.[\/caption]\r\n\r\nFires are commonly associated with earthquakes because fuel pipelines rupture and electrical lines are damaged when the ground shakes (Figure 11.4.3). Most of the damage in the great 1906 San Francisco earthquake was caused by massive fires in the downtown area of the city (Figure 11.4.4). Some 25,000 buildings were destroyed by those fires, which were fuelled by broken gas pipes. Fighting the fires was difficult because water mains had also ruptured. The risk of fires can be reduced through P-wave early warning systems if utility operators can reduce pipeline pressure and close electrical circuits.\r\n\r\n[caption id=\"attachment_500\" align=\"aligncenter\" width=\"900\"]\"\"<\/a> Figure 11.4.3 Some of the effects of the 2011 Tohoku earthquake in the Sendai area of Japan. An oil refinery is on fire, and a vast area has been flooded by a tsunami.[\/caption]\r\n\r\n[caption id=\"attachment_501\" align=\"aligncenter\" width=\"900\"]\"\"<\/a> Figure 11.4.4 Fires in San Francisco following the 1906 earthquake.[\/caption]\r\n\r\n[caption id=\"attachment_502\" align=\"alignright\" width=\"400\"]\"A<\/a> Figure 11.4.5 The Las Colinas debris flow at Santa Tecla (a suburb of the capital San Salvador) triggered by the January 2001 El Salvador earthquake. This is just one of many hundreds of slope failures that resulted from that earthquake. Over 500 people died in the area affected by this slide.[\/caption]\r\n\r\nEarthquakes are important triggers for failures on slopes that are already weak. An example is the Las Colinas slide in the city of Santa Tecla, El Salvador, which was triggered by a M7.6 offshore earthquake in January 2001 (Figure 11.4.5).\r\n\r\nGround shaking during an earthquake can be enough to weaken rock and unconsolidated materials to the point of failure, but in many cases the shaking also contributes to a process known as [pb_glossary id=\"1681\"]liquefaction[\/pb_glossary]<\/strong>, in which an otherwise solid body of sediment is transformed into a liquid mass that can flow. When water-saturated sediments are shaken, the grains become rearranged to the point where they are no longer supporting one another. Instead, the water between the grains is holding them apart and the material can flow. Liquefaction can lead to the collapse of buildings and other structures that might be otherwise undamaged. A good example is the collapse of apartment buildings during the 1964 Niigata earthquake (M7.6) in Japan (Figure 11.4.6). Liquefaction can also contribute to slope failures and to fountains of sandy mud (sand volcanoes) in areas where there is loose saturated sand beneath a layer of more cohesive clay.\r\n\r\n[caption id=\"attachment_503\" align=\"aligncenter\" width=\"500\"]\"\"<\/a> Figure 11.4.6 Collapsed apartment buildings in the Niigata area of Japan. The material beneath the buildings was liquefied to varying degrees by the 1964 earthquake.[\/caption]\r\n\r\nParts of the Fraser River delta are prone to liquefaction-related damage because the region is characterized by a 2 metre to 3 metre thick layer of fluvial silt and clay over top of at least 10 metres of water-saturated fluvial sand (Figure 11.4.7). Under these conditions, it can be expected that seismic shaking will be amplified and that the sandy sediments will liquefy. This could lead to subsidence and tilting of buildings, and to failure and sliding of the silt and clay layer. Current building-code regulations in the Fraser delta area require that measures be taken to strengthen the ground underneath multi-storey buildings prior to construction.\r\n\r\n[caption id=\"attachment_504\" align=\"aligncenter\" width=\"700\"]\"\"<\/a> Figure 11.4.7 Recent unconsolidated sedimentary layers in the Fraser River delta area (top) and the potential consequences in the event of a damaging earthquake.[\/caption]\r\n\r\n
\r\n

Exercise 11.4 Creating liquefaction and discovering the harmonic frequency<\/p>\r\n\r\n<\/header>\r\n

\r\n\r\nThere are a few ways that you can demonstrate the process of liquefaction for yourself. The simplest is to go to a sandy beach (lake, ocean, or river) and find a place near the water\u2019s edge where the sand is wet. This is best done with your shoes off, so let\u2019s hope it\u2019s not too cold! While standing in one place on a wet part of the beach, start moving your feet up and down at a frequency of about once per second. Within a few seconds the previously firm sand will start to lose strength, and you\u2019ll gradually sink in up to your ankles.\r\n\r\n[caption id=\"attachment_505\" align=\"alignright\" width=\"500\"]\"\"<\/a> Figure 11.4.8[\/caption]\r\n\r\nIf you can\u2019t get to a beach, or if the weather isn\u2019t cooperating, put some sand (sandbox sand will do) into a small container, saturate it with water, and then pour the excess water off. You can shake it gently to get the water to separate and then pour the excess water away, and you may have to do that more than once. Place a small rock on the surface of the sand; it should sit there for hours without sinking in. Now, holding the container in one hand gently thump the side or the bottom with your other hand, about twice a second. The rock should gradually sink in as the sand around it becomes liquefied.\r\n\r\nAs you were moving your feet up and down or thumping the pot, it\u2019s likely that you soon discovered the most effective rate for getting the sand to liquefy; this would have been close to the natural harmonic frequency for that body of material. Stepping up and down as fast as you can (several times per second) on the wet beach would not have been effective, nor would you have achieved much by stepping once every several seconds. The body of sand vibrates most readily in response to shaking that is close to its natural harmonic frequency, and liquefaction is also most likely to occur at that frequency.\r\n\r\nSee Appendix 3 for Exercise 11.4 answers<\/a>.\r\n\r\n<\/div>\r\n<\/div>\r\nEarthquakes that take place beneath the ocean have the potential to generate [pb_glossary id=\"1682\"]tsunami[\/pb_glossary]<\/strong>. (Tsunami is the Japanese word for harbour wave. It is the same in both singular and plural.) The most likely situation for a significant tsunami is a large (M7 or greater) subduction-related earthquake. As shown in Figure 11.4.9, during the time between earthquakes the overriding plate becomes distorted by elastic deformation; it is squeezed laterally (Figure 11.4.9B) and pushed up.\r\n\r\n[caption id=\"attachment_506\" align=\"alignright\" width=\"500\"]\"\"<\/a> Figure 11.4.9 Elastic deformation and rebound of overriding plate at a subduction setting (B). The release of the locked zone during an earthquake (C) results in both uplift and subsidence on the sea floor, and this is transmitted to the water overhead, resulting in a tsunami.[\/caption]\r\n\r\nWhen an earthquake happens (Figure 11.4.9C), the plate rebounds and there is both uplift and subsidence on the sea floor, in some cases by as much as several metres vertically over an area of thousands of square kilometres. This vertical motion is transmitted through the water column where it generates a series of waves that then spread across the ocean.\r\n\r\nSubduction earthquakes with magnitude less than 7 do not typically generate significant tsunami because the amount of vertical displacement of the sea floor is minimal. Sea-floor transform earthquakes, even large ones (M7 to M8), don\u2019t typically generate tsunami either, because the motion is mostly side to side, not vertical.\r\n\r\nTsunami waves travel at velocities of several hundred kilometres per hour and easily make it to the far side of an ocean in about the same time as a passenger jet. The simulated one shown in Figure 11.4.10 is similar to that created by the 1700 Cascadia earthquake off the coast of British Columbia, Washington, and Oregon, which was recorded in Japan nine hours later.\r\n\r\n[caption id=\"attachment_507\" align=\"aligncenter\" width=\"800\"]\"\"<\/a> Figure 11.4.10 Model of the tsunami from the 1700 Cascadia earthquake (around M9) showing open-ocean wave heights (colours) and travel time contours. Tsunami wave amplitudes typically increase in shallow water.[\/caption]\r\n\r\nTsunami are discussed further in Chapter 17 under the topic of waves and coasts.\r\n

Media Attributions<\/h2>\r\n